Yale SmartHome Alarm series Spécifications télécharger pdf (Page 18)

or away entry are triggered, the alarm will be

activated immediately.

Stop the Alarm and Alarm

Display

During an alarm, the control panel and outside siren

will sound and dial the emergency phone number.

Thecontrolunitwilldisplay“ALARM!ALARM!”to

notify the user.

Stopping the Alarm

1 Press the disarm key and enter a user code on the

control unit or keypad. The control unit will sound

a long beep and display the device that caused

the alarm. The siren will beep twice and the strobe

will ﬂash side to side.

•Thekeyfobcannotstopanalarmcausedby

burglar or emergency device.

2 When the control unit is displaying the source

of the alarm, pressing any key will display

the telephone number that it dialled out and

acknowledged (if any). If there were more than 2

numbers that were acknowledged the numbers

will be shown by pressing further keys.

3 When “Alarm off” is displayed the system is

disarmed.

Alarm Memory

•Ifanalarmwasraisedduringyourabsence,and

the alarm sequence has been carried out, the

screenwillcontinuouslyshow“ALARM!ALARM!”.

•Disarmthesystemasnormalandthesirenwill

give 3-second alarm sound instead of the normal

two beeps to indicate that there might still be an

intruder still in the house.

•Toclearthedisplay,followthesamestepsas

‘Stopping the Alarm’ described above.

Dialling & Call Acknowledgement

Auto Dialling

•Ifthesystemisinawayarmmode,whenanalarm

occurs the control unit will immediately dial the

preset phone numbers.

•Ifthesystemisinhomemodeordisarmedmode

when an audible alarm is initiated, the control unit

will wait for 15 seconds before dialling the preset

phone numbers.

•Afterdialling,thecontrolpanelwillwait5seconds

then playback the messages in a loop. It will ﬁrst

play the recorded address message then the

pre-recorded messages (Burglar, Emergency)

depending on the nature of the alarm and ﬁnally an

acknowledgement request message.

•Therecipientshouldacknowledgethemessageby

pressing ‘9’ on their telephone when prompted.

•RecipientsusingradioDECTphonesormobiles

should press the numbers repeatedly until the call

is closed.

•Ifthecontrolunitdoesnotreceivean

acknowledgement, the messages will be repeated

for a period of 80 seconds before attempting to

dial again. Each number will have 5 call attempts.

•Thecontrolpanelwillcontinuetodialthe

number(s) until a call is successfully answered with

a ‘9’ acknowledgement.

•Systemauto-diallingfeaturesonlyoperateunder

tone-dialling method.

•Whennotelephonenumberisstored,thecontrol

panel will not dial out.

Remote Access

The control unit allows you to control your system

remotely through the telephone line.

1 Dial the phone number associated with the Control

panel.

2 Hang up on the ﬁrst ring.

3 Wait 5-10 seconds.

4 Dial the number again.

5 The control unit will answer the phone on the ﬁrst

ring of that second call.

6 Enter your PIN Code within 3 seconds.

7 If the PIN code is correct, you will hear a long

beep. A list of different functions is detailed below:

Press 2 Put the system into away armed mode (arm

the system).

Press 3 Disarm the system.

Press 5 Checking the system status. Long single

beep for Away Armed, two beeps for Disarmed and

three beeps for Home Armed.

Press 7 Siren on.

Press 8 Siren off.

Press 9 or 0 Disconnect.

•Remembertopress9or0beforeyouhangup,or

the control unit will hang up automatically after 30

seconds.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Yale SmartHome Alarm series Spécifications Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Yale SmartHome Alarm series