Yale SmartHome Alarm series Spécifications télécharger pdf (Page 14)

Log

The alarm log memorises the last 30 system events

including:

· All alarm events with device names and type

· All fault warning events

· All arming and disarming events

•Theloggedeventsaredisplayedinreversed

chronological order (most recent event ﬁrst).

•Thelogismarkedwitha‘start’labelbeforethe

most recent entry and ‘end’ after the oldest entry.

To view log:

1 Select the Log menu and press 3.

2 The log can now be scrolled up and down and

viewed with the st keys; the most recent event

will be at the start.

3 The ﬁrst line displays the time and date of the

event, the second line displays the type of event

and the third line either states the user or the

device that caused the event. Abbreviations used

are:

· “LB”: low battery

· “Tamp”: tamper

· “R”: restore.

· AC: mains power

· Panic: emergency

· Perimeter: entry or away entry device

· Cancel: silencing an alarm with a help button

Adv. Settings

The settings will initially have factory default values.

If you do not want to change them then you can

escape any menu by pressing P without making

changes.

The following items are available in this menu:

· Pin Code

· Entry Time

· Exit Time

· Entry Sound

· Exit Sound

· Door Chime

· DC Open/Close

· LCD Backlight

· Key Tone

· Ring Tone

· Alarm Length

· C.U. Siren

· Jamming Det

· KF Entry

· Tamper Alarm

· Mobility CHK

· Siren Delay

· Warning Beep

· Time

· Date

· Supervision

Pin Code

The PIN Code (password) is used to conﬁgure the

control unit and to disarm the system.

•Todisarm,pressthe‘disarm’keyfollowedbyyour

PIN code.

•Toentertheprogrammenupressthe‘menu’key,

enter a PIN code followed by 3.

•Upto4Pincodescanbestored.

1 Select ‘Pin Code’ then press 3, a list of 4 PIN

codes will be shown, occupied codes are shown

with ****. The list can be scrolled up and down

using thest keys.

2 Select the code you want to change and press

3, enter your new PIN code and press 3. You will

be asked to repeat the PIN code, enter it again

and conﬁrm by pressing 3, the new code is now

programmed.

•P can be used to correct entry errors, pressing P

repeatedly will return you to the PIN code list.

•User1codecanonlybechangedandcannotbe

erased. All other codes can be erased by selecting

them and pressing 3.

•Anerrormessagewillbeshownifeitheran

incorrect repeat code is used or a duplicate code

is entered for another user. All codes have to be

different.

Entry Time

Note: Ensure device is set to entry on control unit for

the entry time to work (see section 5, Add Devices)

Entry time gives you a delay to allow you time to

enter your premises and disarm the system. Times

can be set from 00 seconds (no delay) up to 70

seconds in 10 second increments.

•20secondsisthefactorydefault.

Exit Time

Entry time gives you a delay to allow you leave you

premises before the system arms. Times can be set

from 00 seconds (no delay) up to 70 seconds in 10

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Yale SmartHome Alarm series Spécifications Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Yale SmartHome Alarm series