Yale HSA3000 Spécifications télécharger pdf (Page 8)

Arming the system

Keypad/Keyfob: Press arm

(The siren will beep/ﬂash once. No audible countdown.)

Disarming the system

Keypad: Press disarm followed by your pincode.

Keyfob: Press disarm.

(The siren will beep twice and ﬂash.)

Stopping the Siren

Keypad: Press disarm followed by your pincode.

Keyfob: Press disarm.

(The siren will be silenced and then beep twice and ﬂash.)

Changing your keypad PIN code

1 Enter setting mode: Press the Panic button A,

followed by entering the current pincode (factory

default code is 0000).

(The LED will now ﬂash continuously.)

2 Press panic button B.

3 Enter new 4-digit pincode.

4 Press Arm button to conﬁrm.

5 Exit setting mode: Press disarm twice to quit the

changing code process. Or wait for 5 minutes for

the keypad to quit test mode automatically.

(The LED will now stop ﬂashing.)

Tamper alarm warning

If any device tamper switches are disturbed a

tamper alarm will be activated with the siren

sounding and the strobe ashing. The alarm can be

silenced as described in “Stopping the Siren”.

Previous alarm warning

Should there be an alarm that was triggered and

expired (while the user was away), the siren will

sound and ash for 3 seconds after disarming (user

returning home).

* Warning: should this happen the intruder could still

be in the premises.

My PIN code:

(write your pincode here so you don’t forget it)

Using the system

Arm and disarm the system and practice using it. Trigger the alarm by arming the system

and opening protected doors/windows and walking past PIRs. Now’s the time to set your pin

code and show the rest of the family how simple it is to use.

• Keypad will arm the system with a 20 seconds

exit period. All detectors will be ignored (except

for the tamper switches). The system can be

armed when inside the protected area of your

premises.

• Keyfob will arm the system instantly without a

20 second exit delay. Any detector activated

afterwards will trigger an instant alarm. The

system should be armed when outside the

protected area of your premises.

• Keypad: If the system has been armed with a

keypad there will be a 20 second entry period

started when the ﬁrst detector is activated

(usually a window/door contact on the main

point of entry). During this entry period all

detectors will be ignored.

• If the system is not disarmed before the entry

period expires, the alarm will be activated.

• The system does not have an audible

countdown during the entry period, however

the siren will beep once when the ﬁrst detector

is triggered.

• Keyfob: If the system has been armed with a

keyfob there will be no 20 second entry period

and any detector activation will give an instant

alarm.

• The system should be disarmed from outside

the protected area of your premises.

• If the PIN code doesn’t change, repeat the

above procedure quickly without gaps.

If there is a persistent siren tamper fault then a

series of 5 pips and ashes will be given when

the system is armed, then the siren should be

checked for any mounting problems and if the

siren lid is secure. Use packing material for

uneven wall surface.

The PIRs have a built-in sleep timer to save

battery power. If there is no movement in front

of the PIRs for 1 minute, the PIRs will become

‘ready to signal’ and movement will now be

reported. The PIRs will sleep for 1 minute after

reporting.

Any movement detected in sleep time will not be

reported and will extend the sleep period by a

further 1 minute.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Yale HSA3000 Spécifications Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Yale HSA3000